1 files changed, 792 insertions, 0 deletions
diff --git a/lib/chibios-contrib/ext/mcux-sdk/devices/K32L2B31A/project_template/pin_mux.c b/lib/chibios-contrib/ext/mcux-sdk/devices/K32L2B31A/project_template/pin_mux.c
new file mode 100644
index 000000000..45286b77d
--- /dev/null
+++ b/lib/chibios-contrib/ext/mcux-sdk/devices/K32L2B31A/project_template/pin_mux.c
@@ -0,0 +1,792 @@
+/*
+ * Copyright 2019 NXP
+ * All rights reserved.
+ *
+ * SPDX-License-Identifier: BSD-3-Clause
+ */
+/***********************************************************************************************************************
+ * This file was generated by the MCUXpresso Config Tools. Any manual edits made to this file
+ * will be overwritten if the respective MCUXpresso Config Tools is used to update this file.
+ **********************************************************************************************************************/
+/* clang-format off */
+/*
+ * TEXT BELOW IS USED AS SETTING FOR TOOLS *************************************
+!!GlobalInfo
+product: Pins v6.0
+processor: K32L2B31xxxxA
+package_id: K32L2B31VLH0A
+mcu_data: ksdk2_0
+processor_version: 0.0.0
+board: FRDM-K32L2B
+pin_labels:
+- {pin_num: '23', pin_signal: PTA1/LPUART0_RX/TPM2_CH0, label: 'J1[2]/D0/UART0_RX', identifier: DEBUG_UART0_RX}
+- {pin_num: '24', pin_signal: PTA2/LPUART0_TX/TPM2_CH1, label: 'J1[4]/D1/UART0_TX', identifier: DEBUG_UART0_TX}
+- {pin_num: '60', pin_signal: LCD_P43/PTD3/SPI0_MISO/UART2_TX/TPM0_CH3/SPI0_MOSI/FXIO0_D3, label: 'J1[6]/D2/LCD_P43', identifier: LCD_P43}
+- {pin_num: '28', pin_signal: PTA12/TPM1_CH0, label: 'J1[8]/D3'}
+- {pin_num: '26', pin_signal: PTA4/I2C1_SDA/TPM0_CH1/NMI_b, label: 'J1[10]/D4/SW1', identifier: SW1}
+- {pin_num: '27', pin_signal: PTA5/USB_CLKIN/TPM0_CH2, label: 'J1[12]/D5/USB_CLKIN', identifier: USB0_CLKIN}
+- {pin_num: '17', pin_signal: CMP0_IN5/ADC0_SE4b/PTE29/TPM0_CH2/TPM_CLKIN0, label: 'J1[14]/D6/CMP0_IN5'}
+- {pin_num: '18', pin_signal: DAC0_OUT/ADC0_SE23/CMP0_IN4/PTE30/TPM0_CH3/TPM_CLKIN1/LPUART1_TX/LPTMR0_ALT1, label: 'J1[16]/J4[11]/D7/CMP0_IN4/DAC_OUT'}
+- {pin_num: '29', pin_signal: PTA13/TPM1_CH1, label: 'J2[2]/D8'}
+- {pin_num: '59', pin_signal: LCD_P42/PTD2/SPI0_MOSI/UART2_RX/TPM0_CH2/SPI0_MISO/FXIO0_D2, label: 'J2[4]/D9/LCD_P42', identifier: LCD_P42}
+- {pin_num: '61', pin_signal: LCD_P44/PTD4/LLWU_P14/SPI1_SS/UART2_RX/TPM0_CH4/FXIO0_D4, label: 'J2[6]/D10/SPI1_PCS0/LCD_P44', identifier: LCD_P44}
+- {pin_num: '63', pin_signal: LCD_P46/ADC0_SE7b/PTD6/LLWU_P15/SPI1_MOSI/LPUART0_RX/SPI1_MISO/FXIO0_D6, label: 'J2[8]/D11/SPI1_MOSI/LCD_P46'}
+- {pin_num: '64', pin_signal: LCD_P47/PTD7/SPI1_MISO/LPUART0_TX/SPI1_MOSI/FXIO0_D7, label: 'J2[10]/D12/SPI1_MISO/LCD_P47'}
+- {pin_num: '62', pin_signal: LCD_P45/ADC0_SE6b/PTD5/SPI1_SCK/UART2_TX/TPM0_CH5/FXIO0_D5, label: 'J2[12]/D13/SPI1_SCK/LED1/LCD_P45', identifier: LED1}
+- {pin_num: '1', pin_signal: LCD_P48/PTE0/CLKOUT32K/SPI1_MISO/LPUART1_TX/RTC_CLKOUT/CMP0_OUT/I2C1_SDA, label: 'J2[18]/J4[9]/D14/I2C1_SDA/CMP0_OUT/LCD_P48', identifier: I2C1_SDA}
+- {pin_num: '2', pin_signal: LCD_P49/PTE1/SPI1_MOSI/LPUART1_RX/SPI1_MISO/I2C1_SCL, label: 'J2[20]/D15/I2C1_SCL/LCD_P49', identifier: I2C1_SCL}
+- {pin_num: '39', pin_signal: LCD_P12/PTB16/SPI1_MOSI/LPUART0_RX/TPM_CLKIN0/SPI1_MISO, label: 'J2[19]/LCD_P12'}
+- {pin_num: '40', pin_signal: LCD_P13/PTB17/SPI1_MISO/LPUART0_TX/TPM_CLKIN1/SPI1_MOSI, label: 'J2[17]/LCD_P13'}
+- {pin_num: '54', pin_signal: LCD_P25/PTC5/LLWU_P9/SPI0_SCK/LPTMR0_ALT2/CMP0_OUT, label: 'J1[15]/INT1_ACCEL/LCD_P25', identifier: INT1_ACCEL}
+- {pin_num: '56', pin_signal: LCD_P27/CMP0_IN1/PTC7/SPI0_MISO/USB_SOF_OUT/SPI0_MOSI, label: 'J1[11]/USB_SOF_OUT/LCD_P27', identifier: LCD_P27}
+- {pin_num: '55', pin_signal: LCD_P26/CMP0_IN0/PTC6/LLWU_P10/SPI0_MOSI/EXTRG_IN/SPI0_MISO, label: 'J1[9]/LCD_P26', identifier: LCD_P26}
+- {pin_num: '53', pin_signal: LCD_P24/PTC4/LLWU_P8/SPI0_SS/LPUART1_TX/TPM0_CH3, label: 'J1[7]/LCD_P24', identifier: LCD_P24}
+- {pin_num: '43', pin_signal: LCD_P20/ADC0_SE14/PTC0/EXTRG_IN/USB_SOF_OUT/CMP0_OUT, label: 'J1[5]/LCD_P20/USB_SOF_OUT', identifier: LCD_P20;USB_SOF_OUT}
+- {pin_num: '42', pin_signal: LCD_P15/PTB19/TPM2_CH1, label: 'J1[3]/LCD_P15', identifier: LCD_P15}
+- {pin_num: '41', pin_signal: LCD_P14/PTB18/TPM2_CH0, label: 'J1[1]/LCD_P14', identifier: LCD_P14}
+- {pin_num: '12', pin_signal: ADC0_DM3/ADC0_SE7a/PTE23/TPM2_CH1/UART2_RX/FXIO0_D7, label: 'J4[7]/DIFF_ADC1_DM'}
+- {pin_num: '11', pin_signal: ADC0_DP3/ADC0_SE3/PTE22/TPM2_CH0/UART2_TX/FXIO0_D6, label: 'J4[5]/DIFF_ADC1_DP'}
+- {pin_num: '10', pin_signal: LCD_P60/ADC0_DM0/ADC0_SE4a/PTE21/TPM1_CH1/LPUART0_RX/FXIO0_D5, label: 'J4[3]/DIFF_ADC0_DM/LCD_P60', identifier: LCD_P60}
+- {pin_num: '9', pin_signal: LCD_P59/ADC0_DP0/ADC0_SE0/PTE20/TPM1_CH0/LPUART0_TX/FXIO0_D4, label: 'J4[1]/DIFF_ADC0_DP/LCD_P59', identifier: LCD_P59}
+- {pin_num: '35', pin_signal: LCD_P0/ADC0_SE8/PTB0/LLWU_P5/I2C0_SCL/TPM1_CH0, label: 'J4[2]/A0/LCD_P0'}
+- {pin_num: '36', pin_signal: LCD_P1/ADC0_SE9/PTB1/I2C0_SDA/TPM1_CH1, label: 'J4[4]/A1/LCD_P1'}
+- {pin_num: '37', pin_signal: LCD_P2/ADC0_SE12/PTB2/I2C0_SCL/TPM2_CH0, label: 'J4[6]/A2/LCD_P2'}
+- {pin_num: '38', pin_signal: LCD_P3/ADC0_SE13/PTB3/I2C0_SDA/TPM2_CH1, label: 'J4[8]/A3/LCD_P3'}
+- {pin_num: '45', pin_signal: LCD_P22/ADC0_SE11/PTC2/I2C1_SDA/TPM0_CH1, label: 'J4[10]/A4/LCD_P22'}
+- {pin_num: '44', pin_signal: LCD_P21/ADC0_SE15/PTC1/LLWU_P6/RTC_CLKIN/I2C1_SCL/TPM0_CH0, label: 'J4[12]/A5/LCD_P21'}
+- {pin_num: '5', pin_signal: USB0_DP, label: 'J10[3]/USB_DP', identifier: USB0_DP}
+- {pin_num: '6', pin_signal: USB0_DM, label: 'J10[2]/USB_DM', identifier: USB0_DM}
+- {pin_num: '22', pin_signal: PTA0/TPM0_CH5/SWD_CLK, label: 'J11[4]/K32L2_SWD_CLK'}
+- {pin_num: '25', pin_signal: PTA3/I2C1_SCL/TPM0_CH0/SWD_DIO, label: 'J11[2]/SWD_DIO_TGTMCU'}
+- {pin_num: '32', pin_signal: EXTAL0/PTA18/LPUART1_RX/TPM_CLKIN0, label: EXTAL_32KHZ, identifier: EXTAL_32KHZ}
+- {pin_num: '33', pin_signal: XTAL0/PTA19/LPUART1_TX/TPM_CLKIN1/LPTMR0_ALT1, label: XTAL_32KHZ, identifier: XTAL_32KHZ}
+- {pin_num: '34', pin_signal: PTA20/RESET_b, label: 'J11[10]/J3[6]/RESET/SW2'}
+- {pin_num: '46', pin_signal: LCD_P23/PTC3/LLWU_P7/SPI1_SCK/LPUART1_RX/TPM0_CH2/CLKOUT, label: SW3/LLWU_P7/LCD_P23, identifier: SW3}
+- {pin_num: '58', pin_signal: LCD_P41/ADC0_SE5b/PTD1/SPI0_SCK/TPM0_CH1/FXIO0_D1, label: 'U2[9]/U10[9]/INT2_ACCEL/INT1_MAG/LCD_P41', identifier: INT2_ACCEL;INT1_MAG}
+- {pin_num: '21', pin_signal: PTE25/TPM0_CH1/I2C0_SDA, label: 'U2[6]/U10[6]/I2C0_SDA', identifier: I2C0_SDA}
+- {pin_num: '20', pin_signal: PTE24/TPM0_CH0/I2C0_SCL, label: 'U2[7]/U10[4]/I2C0_SCL', identifier: I2C0_SCL}
+- {pin_num: '3', pin_signal: VDD17, label: P3V3_K32L2B}
+- {pin_num: '13', pin_signal: VDDA, label: P3V3_K32L2B}
+- {pin_num: '30', pin_signal: VDD94, label: P3V3_K32L2B}
+- {pin_num: '4', pin_signal: VSS18, label: GND}
+- {pin_num: '16', pin_signal: VSSA, label: GND}
+- {pin_num: '31', pin_signal: VSS95, label: GND}
+- {pin_num: '47', pin_signal: VSS136, label: GND}
+- {pin_num: '7', pin_signal: VOUT33, label: VOUT33}
+- {pin_num: '8', pin_signal: VREGIN, label: USB_REGIN, identifier: USB0_VREGIN}
+- {pin_num: '15', pin_signal: VREFL, label: GND}
+- {pin_num: '14', pin_signal: VREFH, label: 'J19[2]/P3V3_K32L2B'}
+- {pin_num: '19', pin_signal: PTE31/TPM0_CH4, label: LED2, identifier: LED2}
+- {pin_num: '48', pin_signal: VLL3, label: 'J12[1]/P3V3_K32L2B'}
+- {pin_num: '49', pin_signal: VLL2/LCD_P4/PTC20, label: TP12/LCD_P4}
+- {pin_num: '50', pin_signal: VLL1/LCD_P5/PTC21, label: TP10/LCD_P5}
+- {pin_num: '51', pin_signal: VCAP2/LCD_P6/PTC22, label: LCD_P6}
+- {pin_num: '52', pin_signal: VCAP1/LCD_P39/PTC23, label: LCD_P39}
+- {pin_num: '57', pin_signal: LCD_P40/PTD0/SPI0_SS/TPM0_CH0/FXIO0_D0, label: LCD-09_P40, identifier: LCD_P40}
+ * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS ***********
+ */
+/* clang-format on */
+#include "fsl_common.h"
+#include "fsl_port.h"
+#include "fsl_gpio.h"
+#include "pin_mux.h"
+/* FUNCTION ************************************************************************************************************
+ *
+ * Function Name : BOARD_InitBootPins
+ * Description   : Calls initialization functions.
+ *
+ * END ****************************************************************************************************************/
+void BOARD_InitBootPins(void)
+{
+    BOARD_InitPins();
+    BOARD_InitDEBUG_UARTPins();
+}
+/* clang-format off */
+/*
+ * TEXT BELOW IS USED AS SETTING FOR TOOLS *************************************
+BOARD_InitPins:
+- options: {callFromInitBoot: 'true', prefix: BOARD_, coreID: core0, enableClock: 'true'}
+- pin_list: []
+ * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS ***********
+ */
+/* clang-format on */
+/* FUNCTION ************************************************************************************************************
+ *
+ * Function Name : BOARD_InitPins
+ * Description   : Configures pin routing and optionally pin electrical features.
+ *
+ * END ****************************************************************************************************************/
+void BOARD_InitPins(void)
+{
+}
+/* clang-format off */
+/*
+ * TEXT BELOW IS USED AS SETTING FOR TOOLS *************************************
+BOARD_InitLCDPins:
+- options: {prefix: BOARD_, coreID: core0, enableClock: 'true'}
+- pin_list:
+  - {pin_num: '41', peripheral: LCD, signal: 'P, 14', pin_signal: LCD_P14/PTB18/TPM2_CH0, slew_rate: slow, pull_select: up, pull_enable: disable}
+  - {pin_num: '42', peripheral: LCD, signal: 'P, 15', pin_signal: LCD_P15/PTB19/TPM2_CH1, slew_rate: slow, pull_select: up, pull_enable: disable}
+  - {pin_num: '43', peripheral: LCD, signal: 'P, 20', pin_signal: LCD_P20/ADC0_SE14/PTC0/EXTRG_IN/USB_SOF_OUT/CMP0_OUT, identifier: LCD_P20, slew_rate: slow, pull_select: up,
+    pull_enable: disable}
+  - {pin_num: '53', peripheral: LCD, signal: 'P, 24', pin_signal: LCD_P24/PTC4/LLWU_P8/SPI0_SS/LPUART1_TX/TPM0_CH3, slew_rate: slow, pull_select: up, pull_enable: disable}
+  - {pin_num: '55', peripheral: LCD, signal: 'P, 26', pin_signal: LCD_P26/CMP0_IN0/PTC6/LLWU_P10/SPI0_MOSI/EXTRG_IN/SPI0_MISO, slew_rate: slow, pull_select: up, pull_enable: disable}
+  - {pin_num: '56', peripheral: LCD, signal: 'P, 27', pin_signal: LCD_P27/CMP0_IN1/PTC7/SPI0_MISO/USB_SOF_OUT/SPI0_MOSI, slew_rate: slow, pull_select: up, pull_enable: disable}
+  - {pin_num: '57', peripheral: LCD, signal: 'P, 40', pin_signal: LCD_P40/PTD0/SPI0_SS/TPM0_CH0/FXIO0_D0, slew_rate: slow, pull_select: up, pull_enable: disable}
+  - {pin_num: '59', peripheral: LCD, signal: 'P, 42', pin_signal: LCD_P42/PTD2/SPI0_MOSI/UART2_RX/TPM0_CH2/SPI0_MISO/FXIO0_D2, slew_rate: slow, pull_select: up, pull_enable: disable}
+  - {pin_num: '60', peripheral: LCD, signal: 'P, 43', pin_signal: LCD_P43/PTD3/SPI0_MISO/UART2_TX/TPM0_CH3/SPI0_MOSI/FXIO0_D3, slew_rate: slow, pull_select: up, pull_enable: disable}
+  - {pin_num: '61', peripheral: LCD, signal: 'P, 44', pin_signal: LCD_P44/PTD4/LLWU_P14/SPI1_SS/UART2_RX/TPM0_CH4/FXIO0_D4, slew_rate: slow, pull_select: up, pull_enable: disable}
+  - {pin_num: '9', peripheral: LCD, signal: 'P, 59', pin_signal: LCD_P59/ADC0_DP0/ADC0_SE0/PTE20/TPM1_CH0/LPUART0_TX/FXIO0_D4, slew_rate: slow, pull_select: up, pull_enable: disable}
+  - {pin_num: '10', peripheral: LCD, signal: 'P, 60', pin_signal: LCD_P60/ADC0_DM0/ADC0_SE4a/PTE21/TPM1_CH1/LPUART0_RX/FXIO0_D5, slew_rate: slow, pull_select: up,
+    pull_enable: disable}
+ * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS ***********
+ */
+/* clang-format on */
+/* FUNCTION ************************************************************************************************************
+ *
+ * Function Name : BOARD_InitLCDPins
+ * Description   : Configures pin routing and optionally pin electrical features.
+ *
+ * END ****************************************************************************************************************/
+void BOARD_InitLCDPins(void)
+{
+    /* Port B Clock Gate Control: Clock enabled */
+    CLOCK_EnableClock(kCLOCK_PortB);
+    /* Port C Clock Gate Control: Clock enabled */
+    CLOCK_EnableClock(kCLOCK_PortC);
+    /* Port D Clock Gate Control: Clock enabled */
+    CLOCK_EnableClock(kCLOCK_PortD);
+    /* Port E Clock Gate Control: Clock enabled */
+    CLOCK_EnableClock(kCLOCK_PortE);
+    /* PORTB18 (pin 41) is configured as LCD_P14 */
+    PORT_SetPinMux(BOARD_LCD_P14_PORT, BOARD_LCD_P14_PIN, kPORT_PinDisabledOrAnalog);
+    PORTB->PCR[18] = ((PORTB->PCR[18] &
+                       /* Mask bits to zero which are setting */
+                       (~(PORT_PCR_PS_MASK | PORT_PCR_PE_MASK | PORT_PCR_SRE_MASK | PORT_PCR_ISF_MASK)))
+                      /* Pull Select: Internal pullup resistor is enabled on the corresponding pin, if the
+                       * corresponding PE field is set. */
+                      | PORT_PCR_PS(kPORT_PullUp)
+                      /* Pull Enable: Internal pullup or pulldown resistor is not enabled on the corresponding
+                       * pin. */
+                      | PORT_PCR_PE(kPORT_PullDisable)
+                      /* Slew Rate Enable: Slow slew rate is configured on the corresponding pin, if the pin is
+                       * configured as a digital output. */
+                      | PORT_PCR_SRE(kPORT_SlowSlewRate));
+    /* PORTB19 (pin 42) is configured as LCD_P15 */
+    PORT_SetPinMux(BOARD_LCD_P15_PORT, BOARD_LCD_P15_PIN, kPORT_PinDisabledOrAnalog);
+    PORTB->PCR[19] = ((PORTB->PCR[19] &
+                       /* Mask bits to zero which are setting */
+                       (~(PORT_PCR_PS_MASK | PORT_PCR_PE_MASK | PORT_PCR_SRE_MASK | PORT_PCR_ISF_MASK)))
+                      /* Pull Select: Internal pullup resistor is enabled on the corresponding pin, if the
+                       * corresponding PE field is set. */
+                      | PORT_PCR_PS(kPORT_PullUp)
+                      /* Pull Enable: Internal pullup or pulldown resistor is not enabled on the corresponding
+                       * pin. */
+                      | PORT_PCR_PE(kPORT_PullDisable)
+                      /* Slew Rate Enable: Slow slew rate is configured on the corresponding pin, if the pin is
+                       * configured as a digital output. */
+                      | PORT_PCR_SRE(kPORT_SlowSlewRate));
+    /* PORTC0 (pin 43) is configured as LCD_P20 */
+    PORT_SetPinMux(BOARD_LCD_P20_PORT, BOARD_LCD_P20_PIN, kPORT_PinDisabledOrAnalog);
+    PORTC->PCR[0] = ((PORTC->PCR[0] &
+                      /* Mask bits to zero which are setting */
+                      (~(PORT_PCR_PS_MASK | PORT_PCR_PE_MASK | PORT_PCR_SRE_MASK | PORT_PCR_ISF_MASK)))
+                     /* Pull Select: Internal pullup resistor is enabled on the corresponding pin, if the
+                      * corresponding PE field is set. */
+                     | PORT_PCR_PS(kPORT_PullUp)
+                     /* Pull Enable: Internal pullup or pulldown resistor is not enabled on the corresponding pin. */
+                     | PORT_PCR_PE(kPORT_PullDisable)
+                     /* Slew Rate Enable: Slow slew rate is configured on the corresponding pin, if the pin is
+                      * configured as a digital output. */
+                     | PORT_PCR_SRE(kPORT_SlowSlewRate));
+    /* PORTC4 (pin 53) is configured as LCD_P24 */
+    PORT_SetPinMux(BOARD_LCD_P24_PORT, BOARD_LCD_P24_PIN, kPORT_PinDisabledOrAnalog);
+    PORTC->PCR[4] = ((PORTC->PCR[4] &
+                      /* Mask bits to zero which are setting */
+                      (~(PORT_PCR_PS_MASK | PORT_PCR_PE_MASK | PORT_PCR_SRE_MASK | PORT_PCR_ISF_MASK)))
+                     /* Pull Select: Internal pullup resistor is enabled on the corresponding pin, if the
+                      * corresponding PE field is set. */
+                     | PORT_PCR_PS(kPORT_PullUp)
+                     /* Pull Enable: Internal pullup or pulldown resistor is not enabled on the corresponding pin. */
+                     | PORT_PCR_PE(kPORT_PullDisable)
+                     /* Slew Rate Enable: Slow slew rate is configured on the corresponding pin, if the pin is
+                      * configured as a digital output. */
+                     | PORT_PCR_SRE(kPORT_SlowSlewRate));
+    /* PORTC6 (pin 55) is configured as LCD_P26 */
+    PORT_SetPinMux(BOARD_LCD_P26_PORT, BOARD_LCD_P26_PIN, kPORT_PinDisabledOrAnalog);
+    PORTC->PCR[6] = ((PORTC->PCR[6] &
+                      /* Mask bits to zero which are setting */
+                      (~(PORT_PCR_PS_MASK | PORT_PCR_PE_MASK | PORT_PCR_SRE_MASK | PORT_PCR_ISF_MASK)))
+                     /* Pull Select: Internal pullup resistor is enabled on the corresponding pin, if the
+                      * corresponding PE field is set. */
+                     | PORT_PCR_PS(kPORT_PullUp)
+                     /* Pull Enable: Internal pullup or pulldown resistor is not enabled on the corresponding pin. */
+                     | PORT_PCR_PE(kPORT_PullDisable)
+                     /* Slew Rate Enable: Slow slew rate is configured on the corresponding pin, if the pin is
+                      * configured as a digital output. */
+                     | PORT_PCR_SRE(kPORT_SlowSlewRate));
+    /* PORTC7 (pin 56) is configured as LCD_P27 */
+    PORT_SetPinMux(BOARD_LCD_P27_PORT, BOARD_LCD_P27_PIN, kPORT_PinDisabledOrAnalog);
+    PORTC->PCR[7] = ((PORTC->PCR[7] &
+                      /* Mask bits to zero which are setting */
+                      (~(PORT_PCR_PS_MASK | PORT_PCR_PE_MASK | PORT_PCR_SRE_MASK | PORT_PCR_ISF_MASK)))
+                     /* Pull Select: Internal pullup resistor is enabled on the corresponding pin, if the
+                      * corresponding PE field is set. */
+                     | PORT_PCR_PS(kPORT_PullUp)
+                     /* Pull Enable: Internal pullup or pulldown resistor is not enabled on the corresponding pin. */
+                     | PORT_PCR_PE(kPORT_PullDisable)
+                     /* Slew Rate Enable: Slow slew rate is configured on the corresponding pin, if the pin is
+                      * configured as a digital output. */
+                     | PORT_PCR_SRE(kPORT_SlowSlewRate));
+    /* PORTD0 (pin 57) is configured as LCD_P40 */
+    PORT_SetPinMux(BOARD_LCD_P40_PORT, BOARD_LCD_P40_PIN, kPORT_PinDisabledOrAnalog);
+    PORTD->PCR[0] = ((PORTD->PCR[0] &
+                      /* Mask bits to zero which are setting */
+                      (~(PORT_PCR_PS_MASK | PORT_PCR_PE_MASK | PORT_PCR_SRE_MASK | PORT_PCR_ISF_MASK)))
+                     /* Pull Select: Internal pullup resistor is enabled on the corresponding pin, if the
+                      * corresponding PE field is set. */
+                     | PORT_PCR_PS(kPORT_PullUp)
+                     /* Pull Enable: Internal pullup or pulldown resistor is not enabled on the corresponding pin. */
+                     | PORT_PCR_PE(kPORT_PullDisable)
+                     /* Slew Rate Enable: Slow slew rate is configured on the corresponding pin, if the pin is
+                      * configured as a digital output. */
+                     | PORT_PCR_SRE(kPORT_SlowSlewRate));
+    /* PORTD2 (pin 59) is configured as LCD_P42 */
+    PORT_SetPinMux(BOARD_LCD_P42_PORT, BOARD_LCD_P42_PIN, kPORT_PinDisabledOrAnalog);
+    PORTD->PCR[2] = ((PORTD->PCR[2] &
+                      /* Mask bits to zero which are setting */
+                      (~(PORT_PCR_PS_MASK | PORT_PCR_PE_MASK | PORT_PCR_SRE_MASK | PORT_PCR_ISF_MASK)))
+                     /* Pull Select: Internal pullup resistor is enabled on the corresponding pin, if the
+                      * corresponding PE field is set. */
+                     | PORT_PCR_PS(kPORT_PullUp)
+                     /* Pull Enable: Internal pullup or pulldown resistor is not enabled on the corresponding pin. */
+                     | PORT_PCR_PE(kPORT_PullDisable)
+                     /* Slew Rate Enable: Slow slew rate is configured on the corresponding pin, if the pin is
+                      * configured as a digital output. */
+                     | PORT_PCR_SRE(kPORT_SlowSlewRate));
+    /* PORTD3 (pin 60) is configured as LCD_P43 */
+    PORT_SetPinMux(BOARD_LCD_P43_PORT, BOARD_LCD_P43_PIN, kPORT_PinDisabledOrAnalog);
+    PORTD->PCR[3] = ((PORTD->PCR[3] &
+                      /* Mask bits to zero which are setting */
+                      (~(PORT_PCR_PS_MASK | PORT_PCR_PE_MASK | PORT_PCR_SRE_MASK | PORT_PCR_ISF_MASK)))
+                     /* Pull Select: Internal pullup resistor is enabled on the corresponding pin, if the
+                      * corresponding PE field is set. */
+                     | PORT_PCR_PS(kPORT_PullUp)
+                     /* Pull Enable: Internal pullup or pulldown resistor is not enabled on the corresponding pin. */
+                     | PORT_PCR_PE(kPORT_PullDisable)
+                     /* Slew Rate Enable: Slow slew rate is configured on the corresponding pin, if the pin is
+                      * configured as a digital output. */
+                     | PORT_PCR_SRE(kPORT_SlowSlewRate));
+    /* PORTD4 (pin 61) is configured as LCD_P44 */
+    PORT_SetPinMux(BOARD_LCD_P44_PORT, BOARD_LCD_P44_PIN, kPORT_PinDisabledOrAnalog);
+    PORTD->PCR[4] = ((PORTD->PCR[4] &
+                      /* Mask bits to zero which are setting */
+                      (~(PORT_PCR_PS_MASK | PORT_PCR_PE_MASK | PORT_PCR_SRE_MASK | PORT_PCR_ISF_MASK)))
+                     /* Pull Select: Internal pullup resistor is enabled on the corresponding pin, if the
+                      * corresponding PE field is set. */
+                     | PORT_PCR_PS(kPORT_PullUp)
+                     /* Pull Enable: Internal pullup or pulldown resistor is not enabled on the corresponding pin. */
+                     | PORT_PCR_PE(kPORT_PullDisable)
+                     /* Slew Rate Enable: Slow slew rate is configured on the corresponding pin, if the pin is
+                      * configured as a digital output. */
+                     | PORT_PCR_SRE(kPORT_SlowSlewRate));
+    /* PORTE20 (pin 9) is configured as LCD_P59 */
+    PORT_SetPinMux(BOARD_LCD_P59_PORT, BOARD_LCD_P59_PIN, kPORT_PinDisabledOrAnalog);
+    PORTE->PCR[20] = ((PORTE->PCR[20] &
+                       /* Mask bits to zero which are setting */
+                       (~(PORT_PCR_PS_MASK | PORT_PCR_PE_MASK | PORT_PCR_SRE_MASK | PORT_PCR_ISF_MASK)))
+                      /* Pull Select: Internal pullup resistor is enabled on the corresponding pin, if the
+                       * corresponding PE field is set. */
+                      | PORT_PCR_PS(kPORT_PullUp)
+                      /* Pull Enable: Internal pullup or pulldown resistor is not enabled on the corresponding
+                       * pin. */
+                      | PORT_PCR_PE(kPORT_PullDisable)
+                      /* Slew Rate Enable: Slow slew rate is configured on the corresponding pin, if the pin is
+                       * configured as a digital output. */
+                      | PORT_PCR_SRE(kPORT_SlowSlewRate));
+    /* PORTE21 (pin 10) is configured as LCD_P60 */
+    PORT_SetPinMux(BOARD_LCD_P60_PORT, BOARD_LCD_P60_PIN, kPORT_PinDisabledOrAnalog);
+    PORTE->PCR[21] = ((PORTE->PCR[21] &
+                       /* Mask bits to zero which are setting */
+                       (~(PORT_PCR_PS_MASK | PORT_PCR_PE_MASK | PORT_PCR_SRE_MASK | PORT_PCR_ISF_MASK)))
+                      /* Pull Select: Internal pullup resistor is enabled on the corresponding pin, if the
+                       * corresponding PE field is set. */
+                      | PORT_PCR_PS(kPORT_PullUp)
+                      /* Pull Enable: Internal pullup or pulldown resistor is not enabled on the corresponding
+                       * pin. */
+                      | PORT_PCR_PE(kPORT_PullDisable)
+                      /* Slew Rate Enable: Slow slew rate is configured on the corresponding pin, if the pin is
+                       * configured as a digital output. */
+                      | PORT_PCR_SRE(kPORT_SlowSlewRate));
+}
+/* clang-format off */
+/*
+ * TEXT BELOW IS USED AS SETTING FOR TOOLS *************************************
+BOARD_InitBUTTONSPins:
+- options: {prefix: BOARD_, coreID: core0, enableClock: 'true'}
+- pin_list:
+  - {pin_num: '26', peripheral: GPIOA, signal: 'GPIO, 4', pin_signal: PTA4/I2C1_SDA/TPM0_CH1/NMI_b, direction: INPUT, slew_rate: fast, pull_select: up, pull_enable: enable,
+    passive_filter: disable}
+  - {pin_num: '46', peripheral: GPIOC, signal: 'GPIO, 3', pin_signal: LCD_P23/PTC3/LLWU_P7/SPI1_SCK/LPUART1_RX/TPM0_CH2/CLKOUT, direction: INPUT, slew_rate: fast,
+    pull_select: up, pull_enable: enable}
+ * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS ***********
+ */
+/* clang-format on */
+/* FUNCTION ************************************************************************************************************
+ *
+ * Function Name : BOARD_InitBUTTONSPins
+ * Description   : Configures pin routing and optionally pin electrical features.
+ *
+ * END ****************************************************************************************************************/
+void BOARD_InitBUTTONSPins(void)
+{
+    /* Port A Clock Gate Control: Clock enabled */
+    CLOCK_EnableClock(kCLOCK_PortA);
+    /* Port C Clock Gate Control: Clock enabled */
+    CLOCK_EnableClock(kCLOCK_PortC);
+    gpio_pin_config_t SW1_config = {
+        .pinDirection = kGPIO_DigitalInput,
+        .outputLogic = 0U
+    };
+    /* Initialize GPIO functionality on pin PTA4 (pin 26)  */
+    GPIO_PinInit(BOARD_SW1_GPIO, BOARD_SW1_PIN, &SW1_config);
+    gpio_pin_config_t SW3_config = {
+        .pinDirection = kGPIO_DigitalInput,
+        .outputLogic = 0U
+    };
+    /* Initialize GPIO functionality on pin PTC3 (pin 46)  */
+    GPIO_PinInit(BOARD_SW3_GPIO, BOARD_SW3_PIN, &SW3_config);
+    const port_pin_config_t SW1 = {/* Internal pull-up resistor is enabled */
+                                   kPORT_PullUp,
+                                   /* Fast slew rate is configured */
+                                   kPORT_FastSlewRate,
+                                   /* Passive filter is disabled */
+                                   kPORT_PassiveFilterDisable,
+                                   /* Low drive strength is configured */
+                                   kPORT_LowDriveStrength,
+                                   /* Pin is configured as PTA4 */
+                                   kPORT_MuxAsGpio};
+    /* PORTA4 (pin 26) is configured as PTA4 */
+    PORT_SetPinConfig(BOARD_SW1_PORT, BOARD_SW1_PIN, &SW1);
+    const port_pin_config_t SW3 = {/* Internal pull-up resistor is enabled */
+                                   kPORT_PullUp,
+                                   /* Fast slew rate is configured */
+                                   kPORT_FastSlewRate,
+                                   /* Passive filter is disabled */
+                                   kPORT_PassiveFilterDisable,
+                                   /* Low drive strength is configured */
+                                   kPORT_LowDriveStrength,
+                                   /* Pin is configured as PTC3 */
+                                   kPORT_MuxAsGpio};
+    /* PORTC3 (pin 46) is configured as PTC3 */
+    PORT_SetPinConfig(BOARD_SW3_PORT, BOARD_SW3_PIN, &SW3);
+}
+/* clang-format off */
+/*
+ * TEXT BELOW IS USED AS SETTING FOR TOOLS *************************************
+BOARD_InitLEDsPins:
+- options: {prefix: BOARD_, coreID: core0, enableClock: 'true'}
+- pin_list:
+  - {pin_num: '19', peripheral: GPIOE, signal: 'GPIO, 31', pin_signal: PTE31/TPM0_CH4, direction: OUTPUT, gpio_init_state: 'true', slew_rate: slow, pull_select: down,
+    pull_enable: disable}
+  - {pin_num: '62', peripheral: GPIOD, signal: 'GPIO, 5', pin_signal: LCD_P45/ADC0_SE6b/PTD5/SPI1_SCK/UART2_TX/TPM0_CH5/FXIO0_D5, direction: OUTPUT, gpio_init_state: 'true',
+    slew_rate: slow, pull_select: down, pull_enable: disable}
+ * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS ***********
+ */
+/* clang-format on */
+/* FUNCTION ************************************************************************************************************
+ *
+ * Function Name : BOARD_InitLEDsPins
+ * Description   : Configures pin routing and optionally pin electrical features.
+ *
+ * END ****************************************************************************************************************/
+void BOARD_InitLEDsPins(void)
+{
+    /* Port D Clock Gate Control: Clock enabled */
+    CLOCK_EnableClock(kCLOCK_PortD);
+    /* Port E Clock Gate Control: Clock enabled */
+    CLOCK_EnableClock(kCLOCK_PortE);
+    gpio_pin_config_t LED1_config = {
+        .pinDirection = kGPIO_DigitalOutput,
+        .outputLogic = 1U
+    };
+    /* Initialize GPIO functionality on pin PTD5 (pin 62)  */
+    GPIO_PinInit(BOARD_LED1_GPIO, BOARD_LED1_PIN, &LED1_config);
+    gpio_pin_config_t LED2_config = {
+        .pinDirection = kGPIO_DigitalOutput,
+        .outputLogic = 1U
+    };
+    /* Initialize GPIO functionality on pin PTE31 (pin 19)  */
+    GPIO_PinInit(BOARD_LED2_GPIO, BOARD_LED2_PIN, &LED2_config);
+    const port_pin_config_t LED1 = {/* Internal pull-up/down resistor is disabled */
+                                    kPORT_PullDisable,
+                                    /* Slow slew rate is configured */
+                                    kPORT_SlowSlewRate,
+                                    /* Passive filter is disabled */
+                                    kPORT_PassiveFilterDisable,
+                                    /* Low drive strength is configured */
+                                    kPORT_LowDriveStrength,
+                                    /* Pin is configured as PTD5 */
+                                    kPORT_MuxAsGpio};
+    /* PORTD5 (pin 62) is configured as PTD5 */
+    PORT_SetPinConfig(BOARD_LED1_PORT, BOARD_LED1_PIN, &LED1);
+    const port_pin_config_t LED2 = {/* Internal pull-up/down resistor is disabled */
+                                    kPORT_PullDisable,
+                                    /* Slow slew rate is configured */
+                                    kPORT_SlowSlewRate,
+                                    /* Passive filter is disabled */
+                                    kPORT_PassiveFilterDisable,
+                                    /* Low drive strength is configured */
+                                    kPORT_LowDriveStrength,
+                                    /* Pin is configured as PTE31 */
+                                    kPORT_MuxAsGpio};
+    /* PORTE31 (pin 19) is configured as PTE31 */
+    PORT_SetPinConfig(BOARD_LED2_PORT, BOARD_LED2_PIN, &LED2);
+}
+/* clang-format off */
+/*
+ * TEXT BELOW IS USED AS SETTING FOR TOOLS *************************************
+BOARD_InitDEBUG_UARTPins:
+- options: {callFromInitBoot: 'true', prefix: BOARD_, coreID: core0, enableClock: 'true'}
+- pin_list:
+  - {pin_num: '23', peripheral: LPUART0, signal: RX, pin_signal: PTA1/LPUART0_RX/TPM2_CH0, slew_rate: fast, pull_select: down, pull_enable: disable}
+  - {pin_num: '24', peripheral: LPUART0, signal: TX, pin_signal: PTA2/LPUART0_TX/TPM2_CH1, direction: OUTPUT, slew_rate: fast, pull_select: down, pull_enable: disable}
+ * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS ***********
+ */
+/* clang-format on */
+/* FUNCTION ************************************************************************************************************
+ *
+ * Function Name : BOARD_InitDEBUG_UARTPins
+ * Description   : Configures pin routing and optionally pin electrical features.
+ *
+ * END ****************************************************************************************************************/
+void BOARD_InitDEBUG_UARTPins(void)
+{
+    /* Port A Clock Gate Control: Clock enabled */
+    CLOCK_EnableClock(kCLOCK_PortA);
+    const port_pin_config_t DEBUG_UART0_RX = {/* Internal pull-up/down resistor is disabled */
+                                              kPORT_PullDisable,
+                                              /* Fast slew rate is configured */
+                                              kPORT_FastSlewRate,
+                                              /* Passive filter is disabled */
+                                              kPORT_PassiveFilterDisable,
+                                              /* Low drive strength is configured */
+                                              kPORT_LowDriveStrength,
+                                              /* Pin is configured as LPUART0_RX */
+                                              kPORT_MuxAlt2};
+    /* PORTA1 (pin 23) is configured as LPUART0_RX */
+    PORT_SetPinConfig(BOARD_DEBUG_UART0_RX_PORT, BOARD_DEBUG_UART0_RX_PIN, &DEBUG_UART0_RX);
+    const port_pin_config_t DEBUG_UART0_TX = {/* Internal pull-up/down resistor is disabled */
+                                              kPORT_PullDisable,
+                                              /* Fast slew rate is configured */
+                                              kPORT_FastSlewRate,
+                                              /* Passive filter is disabled */
+                                              kPORT_PassiveFilterDisable,
+                                              /* Low drive strength is configured */
+                                              kPORT_LowDriveStrength,
+                                              /* Pin is configured as LPUART0_TX */
+                                              kPORT_MuxAlt2};
+    /* PORTA2 (pin 24) is configured as LPUART0_TX */
+    PORT_SetPinConfig(BOARD_DEBUG_UART0_TX_PORT, BOARD_DEBUG_UART0_TX_PIN, &DEBUG_UART0_TX);
+    SIM->SOPT5 = ((SIM->SOPT5 &
+                   /* Mask bits to zero which are setting */
+                   (~(SIM_SOPT5_LPUART0TXSRC_MASK | SIM_SOPT5_LPUART0RXSRC_MASK)))
+                  /* LPUART0 Transmit Data Source Select: LPUART0_TX pin. */
+                  | SIM_SOPT5_LPUART0TXSRC(SOPT5_LPUART0TXSRC_LPUART_TX)
+                  /* LPUART0 Receive Data Source Select: LPUART_RX pin. */
+                  | SIM_SOPT5_LPUART0RXSRC(SOPT5_LPUART0RXSRC_LPUART_RX));
+}
+/* clang-format off */
+/*
+ * TEXT BELOW IS USED AS SETTING FOR TOOLS *************************************
+BOARD_InitUSBPins:
+- options: {prefix: BOARD_, coreID: core0, enableClock: 'true'}
+- pin_list:
+  - {pin_num: '5', peripheral: USB0, signal: DP, pin_signal: USB0_DP}
+  - {pin_num: '6', peripheral: USB0, signal: DM, pin_signal: USB0_DM}
+  - {pin_num: '8', peripheral: USB0, signal: VREGIN, pin_signal: VREGIN}
+  - {pin_num: '43', peripheral: USB0, signal: SOF_OUT, pin_signal: LCD_P20/ADC0_SE14/PTC0/EXTRG_IN/USB_SOF_OUT/CMP0_OUT, identifier: USB_SOF_OUT, slew_rate: fast,
+    pull_select: up, pull_enable: disable}
+  - {pin_num: '27', peripheral: USB0, signal: CLKIN, pin_signal: PTA5/USB_CLKIN/TPM0_CH2, slew_rate: fast, pull_select: up, pull_enable: disable}
+ * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS ***********
+ */
+/* clang-format on */
+/* FUNCTION ************************************************************************************************************
+ *
+ * Function Name : BOARD_InitUSBPins
+ * Description   : Configures pin routing and optionally pin electrical features.
+ *
+ * END ****************************************************************************************************************/
+void BOARD_InitUSBPins(void)
+{
+    /* Port A Clock Gate Control: Clock enabled */
+    CLOCK_EnableClock(kCLOCK_PortA);
+    /* Port C Clock Gate Control: Clock enabled */
+    CLOCK_EnableClock(kCLOCK_PortC);
+    /* PORTA5 (pin 27) is configured as USB_CLKIN */
+    PORT_SetPinMux(BOARD_USB0_CLKIN_PORT, BOARD_USB0_CLKIN_PIN, kPORT_MuxAlt2);
+    PORTA->PCR[5] = ((PORTA->PCR[5] &
+                      /* Mask bits to zero which are setting */
+                      (~(PORT_PCR_PS_MASK | PORT_PCR_PE_MASK | PORT_PCR_SRE_MASK | PORT_PCR_ISF_MASK)))
+                     /* Pull Select: Internal pullup resistor is enabled on the corresponding pin, if the
+                      * corresponding PE field is set. */
+                     | PORT_PCR_PS(kPORT_PullUp)
+                     /* Pull Enable: Internal pullup or pulldown resistor is not enabled on the corresponding pin. */
+                     | PORT_PCR_PE(kPORT_PullDisable)
+                     /* Slew Rate Enable: Fast slew rate is configured on the corresponding pin, if the pin is
+                      * configured as a digital output. */
+                     | PORT_PCR_SRE(kPORT_FastSlewRate));
+    /* PORTC0 (pin 43) is configured as USB_SOF_OUT */
+    PORT_SetPinMux(BOARD_USB_SOF_OUT_PORT, BOARD_USB_SOF_OUT_PIN, kPORT_MuxAlt4);
+    PORTC->PCR[0] = ((PORTC->PCR[0] &
+                      /* Mask bits to zero which are setting */
+                      (~(PORT_PCR_PS_MASK | PORT_PCR_PE_MASK | PORT_PCR_SRE_MASK | PORT_PCR_ISF_MASK)))
+                     /* Pull Select: Internal pullup resistor is enabled on the corresponding pin, if the
+                      * corresponding PE field is set. */
+                     | PORT_PCR_PS(kPORT_PullUp)
+                     /* Pull Enable: Internal pullup or pulldown resistor is not enabled on the corresponding pin. */
+                     | PORT_PCR_PE(kPORT_PullDisable)
+                     /* Slew Rate Enable: Fast slew rate is configured on the corresponding pin, if the pin is
+                      * configured as a digital output. */
+                     | PORT_PCR_SRE(kPORT_FastSlewRate));
+}
+/* clang-format off */
+/*
+ * TEXT BELOW IS USED AS SETTING FOR TOOLS *************************************
+BOARD_InitACCEL_I2CPins:
+- options: {prefix: BOARD_, coreID: core0, enableClock: 'true'}
+- pin_list:
+  - {pin_num: '20', peripheral: I2C0, signal: SCL, pin_signal: PTE24/TPM0_CH0/I2C0_SCL, slew_rate: fast, pull_select: up, pull_enable: enable}
+  - {pin_num: '21', peripheral: I2C0, signal: SDA, pin_signal: PTE25/TPM0_CH1/I2C0_SDA, slew_rate: fast, pull_select: up, pull_enable: enable}
+  - {pin_num: '58', peripheral: GPIOD, signal: 'GPIO, 1', pin_signal: LCD_P41/ADC0_SE5b/PTD1/SPI0_SCK/TPM0_CH1/FXIO0_D1, identifier: INT2_ACCEL, direction: INPUT,
+    slew_rate: fast, pull_select: up, pull_enable: disable}
+  - {pin_num: '54', peripheral: GPIOC, signal: 'GPIO, 5', pin_signal: LCD_P25/PTC5/LLWU_P9/SPI0_SCK/LPTMR0_ALT2/CMP0_OUT, direction: INPUT, slew_rate: fast, pull_select: up,
+    pull_enable: disable}
+ * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS ***********
+ */
+/* clang-format on */
+/* FUNCTION ************************************************************************************************************
+ *
+ * Function Name : BOARD_InitACCEL_I2CPins
+ * Description   : Configures pin routing and optionally pin electrical features.
+ *
+ * END ****************************************************************************************************************/
+void BOARD_InitACCEL_I2CPins(void)
+{
+    /* Port C Clock Gate Control: Clock enabled */
+    CLOCK_EnableClock(kCLOCK_PortC);
+    /* Port D Clock Gate Control: Clock enabled */
+    CLOCK_EnableClock(kCLOCK_PortD);
+    /* Port E Clock Gate Control: Clock enabled */
+    CLOCK_EnableClock(kCLOCK_PortE);
+    gpio_pin_config_t INT1_ACCEL_config = {
+        .pinDirection = kGPIO_DigitalInput,
+        .outputLogic = 0U
+    };
+    /* Initialize GPIO functionality on pin PTC5 (pin 54)  */
+    GPIO_PinInit(BOARD_INT1_ACCEL_GPIO, BOARD_INT1_ACCEL_PIN, &INT1_ACCEL_config);
+    gpio_pin_config_t INT2_ACCEL_config = {
+        .pinDirection = kGPIO_DigitalInput,
+        .outputLogic = 0U
+    };
+    /* Initialize GPIO functionality on pin PTD1 (pin 58)  */
+    GPIO_PinInit(BOARD_INT2_ACCEL_GPIO, BOARD_INT2_ACCEL_PIN, &INT2_ACCEL_config);
+    /* PORTC5 (pin 54) is configured as PTC5 */
+    PORT_SetPinMux(BOARD_INT1_ACCEL_PORT, BOARD_INT1_ACCEL_PIN, kPORT_MuxAsGpio);
+    PORTC->PCR[5] = ((PORTC->PCR[5] &
+                      /* Mask bits to zero which are setting */
+                      (~(PORT_PCR_PS_MASK | PORT_PCR_PE_MASK | PORT_PCR_SRE_MASK | PORT_PCR_ISF_MASK)))
+                     /* Pull Select: Internal pullup resistor is enabled on the corresponding pin, if the
+                      * corresponding PE field is set. */
+                     | PORT_PCR_PS(kPORT_PullUp)
+                     /* Pull Enable: Internal pullup or pulldown resistor is not enabled on the corresponding pin. */
+                     | PORT_PCR_PE(kPORT_PullDisable)
+                     /* Slew Rate Enable: Fast slew rate is configured on the corresponding pin, if the pin is
+                      * configured as a digital output. */
+                     | PORT_PCR_SRE(kPORT_FastSlewRate));
+    /* PORTD1 (pin 58) is configured as PTD1 */
+    PORT_SetPinMux(BOARD_INT2_ACCEL_PORT, BOARD_INT2_ACCEL_PIN, kPORT_MuxAsGpio);
+    PORTD->PCR[1] = ((PORTD->PCR[1] &
+                      /* Mask bits to zero which are setting */
+                      (~(PORT_PCR_PS_MASK | PORT_PCR_PE_MASK | PORT_PCR_SRE_MASK | PORT_PCR_ISF_MASK)))
+                     /* Pull Select: Internal pullup resistor is enabled on the corresponding pin, if the
+                      * corresponding PE field is set. */
+                     | PORT_PCR_PS(kPORT_PullUp)
+                     /* Pull Enable: Internal pullup or pulldown resistor is not enabled on the corresponding pin. */
+                     | PORT_PCR_PE(kPORT_PullDisable)
+                     /* Slew Rate Enable: Fast slew rate is configured on the corresponding pin, if the pin is
+                      * configured as a digital output. */
+                     | PORT_PCR_SRE(kPORT_FastSlewRate));
+    const port_pin_config_t I2C0_SCL = {/* Internal pull-up resistor is enabled */
+                                        kPORT_PullUp,
+                                        /* Fast slew rate is configured */
+                                        kPORT_FastSlewRate,
+                                        /* Passive filter is disabled */
+                                        kPORT_PassiveFilterDisable,
+                                        /* Low drive strength is configured */
+                                        kPORT_LowDriveStrength,
+                                        /* Pin is configured as I2C0_SCL */
+                                        kPORT_MuxAlt5};
+    /* PORTE24 (pin 20) is configured as I2C0_SCL */
+    PORT_SetPinConfig(BOARD_I2C0_SCL_PORT, BOARD_I2C0_SCL_PIN, &I2C0_SCL);
+    const port_pin_config_t I2C0_SDA = {/* Internal pull-up resistor is enabled */
+                                        kPORT_PullUp,
+                                        /* Fast slew rate is configured */
+                                        kPORT_FastSlewRate,
+                                        /* Passive filter is disabled */
+                                        kPORT_PassiveFilterDisable,
+                                        /* Low drive strength is configured */
+                                        kPORT_LowDriveStrength,
+                                        /* Pin is configured as I2C0_SDA */
+                                        kPORT_MuxAlt5};
+    /* PORTE25 (pin 21) is configured as I2C0_SDA */
+    PORT_SetPinConfig(BOARD_I2C0_SDA_PORT, BOARD_I2C0_SDA_PIN, &I2C0_SDA);
+}
+/* clang-format off */
+/*
+ * TEXT BELOW IS USED AS SETTING FOR TOOLS *************************************
+BOARD_InitOSCPins:
+- options: {prefix: BOARD_, coreID: core0, enableClock: 'true'}
+- pin_list:
+  - {pin_num: '32', peripheral: OSC0, signal: EXTAL0, pin_signal: EXTAL0/PTA18/LPUART1_RX/TPM_CLKIN0, slew_rate: no_init, pull_select: no_init, pull_enable: no_init}
+  - {pin_num: '33', peripheral: OSC0, signal: XTAL0, pin_signal: XTAL0/PTA19/LPUART1_TX/TPM_CLKIN1/LPTMR0_ALT1, slew_rate: no_init, pull_select: no_init, pull_enable: no_init}
+ * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS ***********
+ */
+/* clang-format on */
+/* FUNCTION ************************************************************************************************************
+ *
+ * Function Name : BOARD_InitOSCPins
+ * Description   : Configures pin routing and optionally pin electrical features.
+ *
+ * END ****************************************************************************************************************/
+void BOARD_InitOSCPins(void)
+{
+    /* Port A Clock Gate Control: Clock enabled */
+    CLOCK_EnableClock(kCLOCK_PortA);
+    /* PORTA18 (pin 32) is configured as EXTAL0 */
+    PORT_SetPinMux(BOARD_EXTAL_32KHZ_PORT, BOARD_EXTAL_32KHZ_PIN, kPORT_PinDisabledOrAnalog);
+    /* PORTA19 (pin 33) is configured as XTAL0 */
+    PORT_SetPinMux(BOARD_XTAL_32KHZ_PORT, BOARD_XTAL_32KHZ_PIN, kPORT_PinDisabledOrAnalog);
+}
+/***********************************************************************************************************************
+ * EOF
+ **********************************************************************************************************************/